📞 0800 276 1200
Installation Guide

How to Install Venetian Blinds

Your venetian blinds are made to measure and come with box brackets, so fitting them is quick. Follow these six steps for timber, faux wood and aluminium venetians, inside or outside fit. Most blinds are up in about 15 minutes.

✓ About 15 minutes a blind ✓ Inside & outside fit ✓ 5-year warranty
Venetian blinds fitted neatly to a living-room window
Before you start

What you'll need

Unpack each blind carefully and leave it fully pulled up while you fit it. Ordered several blinds? Match each one to its window by width before you drill.

Tools

  • Drill and drill bits
  • Phillips screwdriver
  • Spirit level and tape measure
  • Pencil and a step ladder
  • A helper for wide blinds

Screws and fixings

  • Timber frames: wood screws
  • Plasterboard: wall plugs or toggles
  • Aluminium joinery: self-tapping screws
  • Near the edge of a timber frame, pre-drill a small pilot hole so it doesn't split
In the box

What comes with your blind

Blind

Headrail, slats and bottom rail, already assembled.

Box brackets

One for each end, plus a centre support on wider blinds.

Valance

The front cover strip, with clips or Velcro to fix it.

Cords

A lift cord to raise and lower, and tilt cords to angle the slats.

Check first

Inside fit or outside fit?

Your blind was made for one of these, so fit it the way you measured it. The same box brackets do both. Not sure which you ordered? See our how to measure guide or give us a call.

Inside fit

The blind sits inside the window frame. Fix a bracket at each end up into the top of the recess (top fix), set back from the front so the valance sits flush.

Outside fit

The blind sits on the wall above the window and overlaps each side. Fix the brackets back into the wall or architrave (face fix), level, with the same overlap each side.

Six steps

Fitting your venetian blind

1

Open the brackets

Each bracket has a front that swings open. Press the locking tab on the underside and lift the front up. Open both brackets before you start.

2

Fix the brackets

  • Inside fit: screw a bracket into each end of the recess, up into the top, set back from the front edge so the valance sits flush.
  • Outside fit: mark the brackets on the wall or architrave so the blind overlaps evenly each side, and fix into solid timber.

Tip: The brackets have screw holes in the top, back and sides, so use whichever suits your window.

3

Fit the centre support (wide blinds)

Fix the centre support near the middle, with its back lined up with the back of the box brackets, and keep it clear of the cords and ladder strings so the slats tilt freely.

4

Slide the blind in

Hold the headrail with the cords facing you and slide it straight back until it sits fully inside both brackets. Get a helper on wide blinds.

5

Lock the brackets

Lower the front of each bracket until the locking tab clicks. Give the headrail a gentle tug: it shouldn't move forward or drop out.

6

Fit the valance

  • Faux wood (PVC): push the valance onto the clips on the front of the headrail.
  • Timber (cedar): peel the backing off the Velcro pads, line the valance up evenly and press it onto the headrail.
Everyday use

Using your blind

pull towardsthe centre

Lowering

Pull the lift cord gently towards the centre of the blind to release the lock, then let the cord feed back up slowly as the blind comes down.

pull down,then to the side

Raising & locking

Pull the lift cord straight down to raise the blind. To hold it at any height, move the cord out towards the side of the blind and let go.

pull one cord orthe other to tilt

Tilting the slats

Pull one tilt cord to angle the slats one way and the other cord to angle them back. Tilt slats up for privacy while still letting light in.

Need to take a blind down for cleaning? Raise it fully, take off the valance, open the front of each bracket and slide the blind out towards you. Our care and cleaning guide covers the rest.

Troubleshooting

If something's not right

ProblemWhat to check
Blind won't stay upMove the lift cord out towards the side of the blind before letting go, so the lock can catch it. Pulling it towards the centre releases it.
Slats don't tilt smoothlyCheck the centre support bracket isn't touching the cords or ladder strings. Open the brackets, slide the blind out and move the centre support along a little.
Headrail won't slide inCheck the front of each bracket is fully lifted open, and that the brackets are level and in a straight line.
Bottom rail is crookedCheck the headrail is level first. Then lower the blind all the way and raise it again evenly.
Brackets won't lockMake sure the headrail is pushed fully back into both brackets, then press the front down firmly until the tab clicks.

Rather we fit them for you?

We install venetian blinds across Auckland, backed by our 5-year warranty. Stuck partway through a DIY install? Call us on 0800 276 1200, Monday to Friday, 8:30am to 4:30pm.

Book a free measure & quote →
Good to know

Installing venetian blinds: FAQs

Can I install venetian blinds myself?

Yes. Your venetian blinds are made to measure and come with box brackets, so fitting them is a simple job with a drill, a spirit level and a screwdriver. Most blinds take about 15 minutes. Wider blinds are easier with a second person.

Should the brackets go into the top of the recess or into the wall?

It depends how the blind was measured. For an inside fit, screw the brackets up into the top of the window recess (top fix). For an outside fit, screw them back into the wall or frame above the window (face fix). The same box brackets do both.

How do the box brackets open and lock?

Press the locking tab on the underside of the bracket and lift the front up to open it. Once the headrail is in, lower the front again until the tab clicks.

What is the centre support bracket for?

Wider blinds come with a centre support bracket to hold up the middle of the headrail. Fix it near the middle, lined up with the back of the box brackets, and keep it clear of the cords and ladder strings so the slats tilt freely.

How do I attach the valance?

Faux wood (PVC) valances push onto clips on the front of the headrail. Timber (cedar) valances attach with Velcro pads: peel off the backing, line the valance up evenly and press it onto the headrail.

Why won't my venetian blind stay up?

The cord lock only catches when the lift cord is moved out towards the side of the blind. Pull the cord down, swing it out to the side and let go. Pulling the cord towards the centre of the blind releases the lock.

Can you install the blinds for me?

Yes. We install across Auckland, and our team can measure and fit your venetian blinds for you. Call 0800 276 1200 or book a free measure and quote.